T-Floors to be casted upon

Anders Beton supplies various T-floors to be casted upon for use in cattle barns. All T-floors have been calculated for use in the agricultural environment XA3 for a long lifespan.

Benefits of T-Floors to be casted upon
  • Calculated for XA3 environmental class
  • Applicable for cubicle beds to feed alleys
  • Short installation time
  • Strongly armed for minimal depositing

Information T-Floors to be casted upon

Work T-floor walkable after concrete cast Type 503.000BL
LENGTH WIDTH HEIGHT WEIGHT REF. NUMBER
200 120 12 390 kg 503.200BL
210 120 12 411 kg 503.210BL
220 120 12 430 kg 503.220BL
225 120 12 440 kg 503.225BL
230 120 12 450 kg 503.230BL
235 120 12 460 kg 503.235BL
240 120 12 469 kg 503.240BL
245 120 12 479 kg 503.245BL
250 120 12 489 kg 503.250BL
260 120 12 509 kg 503.260BL
270 120 12 528 kg 503.270BL
300 120 12 587 kg 503.300BL

Loads / Filling requirements
The finished and cured floor has a load capacity of 500 kg per m². Raised floors of this type with a length of more than 270 cm must be supported prior to filling.

Total floor thickness

  • ≤ 270 cm: deposit to 81 litres of concrete C20/25 per m² so that you obtain a total floor thickness of 15cm.
  • > 275 cm: deposit to 101 litres of concrete C20/25 per m² so that you obtain a total floor thickness of 17 cm.

Other lengths are available per 5cm with price adjustment.

Work T-floor drivable after concrete cast Type 509.000BR
LENGTH WIDTH HEIGHT WEIGHT REF. NUMBER
200 120 12 369 kg 509.200BR
220 120 12 436 kg 509.220BR
250 120 12 495 kg 509.250BR
255 120 12 505 kg 509.255BR
270 120 12 535 kg 509.270BR
275 120 12 545 kg 509.275BR
300 120 12 594 kg 509.300BR
350 120 12 693 kg 509.350BR
Loads / Filling requirements
The finished and cured floor is drivable with:
  • Axle load while driving of 12.5tons – wheel tracking distance 2m – wheel base 1.2m – wheel print 40x40cm;
  • Tilt position axle load of 15tons – wheel tracking distance 2m – wheel base 2m - wheel print 40x40cm.

Raised floors of this type with a length of more than 350 cm must be supported prior to filling. Load capacity on request.

Total floor thickness

  • ≤ 300 cm: deposit to 109 litres of concrete C20/25 per m² so that you obtain a total floor thickness of 18 cm.
  • from 305 to 350 cm: deposit to 139 litres of concrete C20/25 per m² so that you obtain a total floor thickness of 21 cm.

Other lengths are available per 5cm with price adjustment.

Step 1: Fit floor elements

Step 2: Place insert composite (in between the plates)

               Net 06/150                                        

fase 2
Step 3: Place shrinkage composite (on top)

               Net 06/150                                        

fase 3

About the entire floor at 3cm from top of finished floor.

Step 4: Support reinforcement

fase 4

The design engineer in charge should be consulted for the correct support reinforcement.

Omschrijving Type
AB Cattle Brochure English Folders Download
General conditions of sale Sales Conditions Download